# Buliding my own computer phase 1

**URL:** <https://forum.kirupa.com/t/buliding-my-own-computer-phase-1/59790>\
**Category:** random\
**Created:** [August 3, 2004, 10:25pm UTC](https://forum.kirupa.com/t/buliding-my-own-computer-phase-1/59790 "2004-08-03T22:25:38Z")\
**Posts on this page:** 20\
**Page:** 3

<div class="post-metadata">

**Author:** ![system](https://canada1.discourse-cdn.com/flex011/uploads/kirupa/original/3X/6/2/621e5c11736f46532526e61be85940af4230f3e5.png) [@system](https://forum.kirupa.com/u/system)\
**Post date:** [August 4, 2004, 10:49pm UTC](https://forum.kirupa.com/t/buliding-my-own-computer-phase-1/59790/41 "2004-08-04T22:49:11Z")

</div>

> [@Voetsjoeba](#):
>
> Man … you are so lucky to have an AlienWare comp, plus your dual monitor setup !
> 
> Anyway - since you are trying to compete with your AWare comp (which will be a tough job since AWare is the top of the notch when it comes to extreme speed), you’ll have to get yourself some expensive and speedy stuff. Here are a few guidelines:
> 
> - The processor - make sure you have a processor that’s as fast as possible. I would suggest checking out those new Athlon64’s - they run at 64bit, where all other processors run at 32bit. They can handle twice as much as others. I think the fastest model of the Athlon64 is 3800+. Not bad, aye ?
> 
> **Exactly, but put cost into perspective and you might want it dubed down to a lower 64bit version.**
> 
> - FSB - make sure your FSB (Front Side Bus) is as fast as possible. The FSB is the connection between the processor and the rest of your computer, so the faster the FSB, the faster the whole system. 333 Mhz is the absolute minimum, 800 Mhz is recommended. If you can find faster, go with the faster one.
> 
> **64Bit processor = 800Mhz+ FSB**
> 
> - Hard Drive - You should get a HD with of course enough capacity, but the RPM (Rotations Per Minute) is also important. The higher the RPM, the faster the disk can read and write data. Today the top is 10,000 RPM, and the common standard is 7,000 RPM. The Western Digital Raptor is one that runs at 10,000 RPM, you might wanna look into it. And, if you want and additional extreme performance boost, then I suggest setting up a RAID-0 striping system. That means that you connect two HD’s that are controlled as one, resulting in doubling the read access and write access time. Very performant setup.
> 
> **Go with either Western Digital or Seagate only. Maxtor, Hitachi, etc are too fragile.**
> 
> - Motherboard - Always make sure that you get a motherboard that supports the processor of your choice, has an as fast FSB as possible, has at least AGP 8x, and as much PCI slots as possible (5 is a good amount). PCI Express is a bonus, but not required.
> 
> **Refer to my last post.**
> 
> - GFX card - Simply get the fastest you can find, preferably ATI. nVidia cards seem to get very hot lately (too hot, really), and they’re already squeezing every bit of performance out of their cards with their drivers, whereas ATI cards don’t get as hot, look much cooler, and the drivers aren’t perfect yet, though they’re already faster than nVidia cards. If you’re going for an nVidia based card, avoid ones that have a huge cooler system that takes up the PCI slot next to the AGP slot. A very fast one (though not sure if it’s the fastest, but it’ll be close) is the ATI X800 XT. God, it’s fast.
> 
> **nVidia or ATI is up to you depending on your budget, the most expensive doesn’t mean it’s the best.**
> 
> That’s about the most important stuff.

---

<div class="post-metadata">

**Author:** ![system](https://canada1.discourse-cdn.com/flex011/uploads/kirupa/original/3X/6/2/621e5c11736f46532526e61be85940af4230f3e5.png) [@system](https://forum.kirupa.com/u/system)\
**Post date:** [August 4, 2004, 10:53pm UTC](https://forum.kirupa.com/t/buliding-my-own-computer-phase-1/59790/42 "2004-08-04T22:53:53Z")

</div>

> 333 Mhz is the absolute minimum, 800 Mhz is recommended. If you can find faster, go with the faster one.

Macs can go to 1.25 Ghz FBS… 😛

---

<div class="post-metadata">

**Author:** ![system](https://canada1.discourse-cdn.com/flex011/uploads/kirupa/original/3X/6/2/621e5c11736f46532526e61be85940af4230f3e5.png) [@system](https://forum.kirupa.com/u/system)\
**Post date:** [August 4, 2004, 10:55pm UTC](https://forum.kirupa.com/t/buliding-my-own-computer-phase-1/59790/43 "2004-08-04T22:55:49Z")

</div>

_drools_

I’m getting excited by all this. Can I build a super computer with $2,000 Canadian? I mean one with the 64 bit, 3.6ghz etc?

---

<div class="post-metadata">

**Author:** ![system](https://canada1.discourse-cdn.com/flex011/uploads/kirupa/original/3X/6/2/621e5c11736f46532526e61be85940af4230f3e5.png) [@system](https://forum.kirupa.com/u/system)\
**Post date:** [August 4, 2004, 10:58pm UTC](https://forum.kirupa.com/t/buliding-my-own-computer-phase-1/59790/44 "2004-08-04T22:58:14Z")

</div>

Definetly CG,  
with ease 😉

---

<div class="post-metadata">

**Author:** ![system](https://canada1.discourse-cdn.com/flex011/uploads/kirupa/original/3X/6/2/621e5c11736f46532526e61be85940af4230f3e5.png) [@system](https://forum.kirupa.com/u/system)\
**Post date:** [August 4, 2004, 11:11pm UTC](https://forum.kirupa.com/t/buliding-my-own-computer-phase-1/59790/45 "2004-08-04T23:11:28Z")

</div>

You think you’re excited? Hardware turns me on.

---

<div class="post-metadata">

**Author:** ![system](https://canada1.discourse-cdn.com/flex011/uploads/kirupa/original/3X/6/2/621e5c11736f46532526e61be85940af4230f3e5.png) [@system](https://forum.kirupa.com/u/system)\
**Post date:** [August 4, 2004, 11:16pm UTC](https://forum.kirupa.com/t/buliding-my-own-computer-phase-1/59790/46 "2004-08-04T23:16:53Z")

</div>

> [@Maxtr0sity](#):
>
> You think you’re excited? Hardware turns me on.

Just the word **gigabyte** gives my the goosebumps… 😛

When I hear my power supply kick in, and my HD’s start running, it’s like Barry White to my ears.

---

<div class="post-metadata">

**Author:** ![system](https://canada1.discourse-cdn.com/flex011/uploads/kirupa/original/3X/6/2/621e5c11736f46532526e61be85940af4230f3e5.png) [@system](https://forum.kirupa.com/u/system)\
**Post date:** [August 4, 2004, 11:19pm UTC](https://forum.kirupa.com/t/buliding-my-own-computer-phase-1/59790/47 "2004-08-04T23:19:04Z")

</div>

> [@grinch](#):
>
> When I hear my power supply kick in, and my HD’s start running, it’s like Barry White to my ears.

:geek:😉

---

<div class="post-metadata">

**Author:** ![system](https://canada1.discourse-cdn.com/flex011/uploads/kirupa/original/3X/6/2/621e5c11736f46532526e61be85940af4230f3e5.png) [@system](https://forum.kirupa.com/u/system)\
**Post date:** [August 4, 2004, 11:20pm UTC](https://forum.kirupa.com/t/buliding-my-own-computer-phase-1/59790/48 "2004-08-04T23:20:11Z")

</div>

Can’t say the same. I have a piece of over tweaked out junk that’s basically better at being a footrest than anything else.

---

<div class="post-metadata">

**Author:** ![system](https://canada1.discourse-cdn.com/flex011/uploads/kirupa/original/3X/6/2/621e5c11736f46532526e61be85940af4230f3e5.png) [@system](https://forum.kirupa.com/u/system)\
**Post date:** [August 4, 2004, 11:20pm UTC](https://forum.kirupa.com/t/buliding-my-own-computer-phase-1/59790/49 "2004-08-04T23:20:34Z")

</div>

Lol not as much as when I hear my turbo rev in an 86 corolla while drifting at extreme angles… :nerd:

---

<div class="post-metadata">

**Author:** ![system](https://canada1.discourse-cdn.com/flex011/uploads/kirupa/original/3X/6/2/621e5c11736f46532526e61be85940af4230f3e5.png) [@system](https://forum.kirupa.com/u/system)\
**Post date:** [August 4, 2004, 11:29pm UTC](https://forum.kirupa.com/t/buliding-my-own-computer-phase-1/59790/50 "2004-08-04T23:29:29Z")

</div>

86’ Corolla, not bad but I personally prefer my 88’ Mustang.

---

<div class="post-metadata">

**Author:** ![system](https://canada1.discourse-cdn.com/flex011/uploads/kirupa/original/3X/6/2/621e5c11736f46532526e61be85940af4230f3e5.png) [@system](https://forum.kirupa.com/u/system)\
**Post date:** [August 5, 2004, 12:30am UTC](https://forum.kirupa.com/t/buliding-my-own-computer-phase-1/59790/51 "2004-08-05T00:30:24Z")

</div>

1999 Corolla, in-line 4 baby!

---

<div class="post-metadata">

**Author:** ![system](https://canada1.discourse-cdn.com/flex011/uploads/kirupa/original/3X/6/2/621e5c11736f46532526e61be85940af4230f3e5.png) [@system](https://forum.kirupa.com/u/system)\
**Post date:** [August 7, 2004, 12:33am UTC](https://forum.kirupa.com/t/buliding-my-own-computer-phase-1/59790/52 "2004-08-07T00:33:00Z")

</div>

> I’m getting excited by all this. Can I build a super computer with $2,000 Canadian? I mean one with the 64 bit, 3.6ghz etc?

I don’t know if 64 bit is the way to go at this point and time. I read an article comparing the 64 bit AMD processors to some of Intel’s newer processors (with prescott architecture), and the 64 bit chips just couldn’t keep up. Of course, another article might say the exact opposite (you can trust everything you read on the internet).

As for building your own computer, these are things I would do/look for:

1. I would use an intel motherboard. Make sure it has AGP 8x, and PCI-x would be cool too (although those might be too pricey). Make sure it supports 800 mhz front side bus. Make sure it supports the prescott chip. Make sure it supports DDR 400 memory (I think that’s the fastest they have right now). Make sure it supports serial ATA hard drives. On board sound would be good, but I would try to find a mobo without onboard video (you’ll want to use your own card anyway).

2. I would use an intel processor (what can I say? I’m an intel man). Pentium 4, hyperthreading, 800 mhz front side bus, prescott architecture.

3. I have no preference on memory. Kingston is a good company. You’ll probably want 1 gigabyte of DDR 400 memory.

4. I would go with an NVidia video card. Geforce 4 ti cards are fast and relatively cheap now, or you could go all out and get the top of the line NVidia.

5. I would use a Seagate Barracuda or Western Digital Harddrive. Make sure it’s a serial ATA drive (7200 RPM minimum).

6. I would get whatever case has a large enough power supply, enough bays, and is the cheapest…who cares what your machine looks like.

That’s pretty much it, you’ll also want to pick up a floppy drive and 52x CDRW (maybe even a DVD burner??? make sure it’s dual layer!).

-teet

---

<div class="post-metadata">

**Author:** ![system](https://canada1.discourse-cdn.com/flex011/uploads/kirupa/original/3X/6/2/621e5c11736f46532526e61be85940af4230f3e5.png) [@system](https://forum.kirupa.com/u/system)\
**Post date:** [August 7, 2004, 1:41am UTC](https://forum.kirupa.com/t/buliding-my-own-computer-phase-1/59790/53 "2004-08-07T01:41:24Z")

</div>

> [@teet](#):
>
> I don’t know if 64 bit is the way to go at this point and time. I read an article comparing the 64 bit AMD processors to some of Intel’s newer processors (with prescott architecture), and the 64 bit chips just couldn’t keep up. Of course, another article might say the exact opposite (you can trust everything you read on the internet).
> 
> As for building your own computer, these are things I would do/look for:
> 
> 1. I would use an intel motherboard. Make sure it has AGP 8x, and PCI-x would be cool too (although those might be too pricey). Make sure it supports 800 mhz front side bus. Make sure it supports the prescott chip. Make sure it supports DDR 400 memory (I think that’s the fastest they have right now). Make sure it supports serial ATA hard drives. On board sound would be good, but I would try to find a mobo without onboard video (you’ll want to use your own card anyway).
> 
> **AGP 8x is a waste of money, stick with 4. Intel motherboards aren’t for pros. AMD is the way to go. Plus, AMD makes the best 64bit so far. Mobo video isn’t the worste idea for an extra buck or two considering if your video card poops, at least you have a backup to attempt to fix it.**
> 
> 1. I would use an intel processor (what can I say? I’m an intel man). Pentium 4, hyperthreading, 800 mhz front side bus, prescott architecture.
> 
> **Defeats the purpose of the 64bit processor doesn’t it?**
> 
> 1. I have no preference on memory. Kingston is a good company. You’ll probably want 1 gigabyte of DDR 400 memory.
> 
> 2. I would go with an NVidia video card. Geforce 4 ti cards are fast and relatively cheap now, or you could go all out and get the top of the line NVidia.
> 
> **ATI scores higher in general than nVidia cards. Since they’re in the same price range, go with ATI.**
> 
> 1. I would use a Seagate Barracuda or Western Digital Harddrive. Make sure it’s a serial ATA drive (7200 RPM minimum).
> 
> **Orrrrrrr…Raid!**
> 
> 1. I would get whatever case has a large enough power supply, enough bays, and is the cheapest…who cares what your machine looks like.
> 
> **300W minimum. Cases are important for heat disipation, definitely a full tower.**
> 
> That’s pretty much it, you’ll also want to pick up a floppy drive and 52x CDRW (maybe even a DVD burner??? make sure it’s dual layer!).
> 
> -teet

---

<div class="post-metadata">

**Author:** ![system](https://canada1.discourse-cdn.com/flex011/uploads/kirupa/original/3X/6/2/621e5c11736f46532526e61be85940af4230f3e5.png) [@system](https://forum.kirupa.com/u/system)\
**Post date:** [August 7, 2004, 1:51am UTC](https://forum.kirupa.com/t/buliding-my-own-computer-phase-1/59790/54 "2004-08-07T01:51:58Z")

</div>

What good is a 64-bit processor if you do not have applications running running in 64-bit. The reason I pick an Intel over AMD almost always is that, at least in the past, when the CPU overheated, Intel CPUs contained built-in technology that prevented the CPU from melting. Intel, in my view, simply makes better quality products. I would rather use the intel mobo reference designs over an AMD any day. My choice of Intel is part personal preference and part bad experiences with AMD in the past.

About the video card on the mobo, I’m going to have to disagree max! Nothing that is embedded on your motherboard is good. See I’m a Right Wing Conservative…when it comes to computers 😛 The motherboard has to have limited powers. The motherboard’s only job is the make sure that all its citizen PCI/AGP cards don’t run away. Something that is embedded means that it can’t be upgraded in the future, and if some hardware conflict occurs, you may have some issues trying to disable something that is attached to your motherboard. Impeaching troublesome hardware is more difficult if that hardware is stuck on the motherboard itself. Also, for the most part, graphics cards from reputable manufacturers such as Hercules, Sapphire, etc. don’t have a high likelihood of failing.

Also, AGP 8X is what you need for today’s games. Unlike 64-bit processing, old and new games will take advantage of the extra data throughput offered by AGP 8X.

EDIT: Also, I’ve been tempted by ATI because of their lower prices (and I even bought a new ATI a few weeks ago!), but their shoddy driver support makes me regret my choice everytime. The new nVidia card is not all that bad, and it is capable of playing all new games. Better drivers imo are far better than a few fps that your eyes probably will never recognize.

:ub:

---

<div class="post-metadata">

**Author:** ![system](https://canada1.discourse-cdn.com/flex011/uploads/kirupa/original/3X/6/2/621e5c11736f46532526e61be85940af4230f3e5.png) [@system](https://forum.kirupa.com/u/system)\
**Post date:** [August 7, 2004, 2:03am UTC](https://forum.kirupa.com/t/buliding-my-own-computer-phase-1/59790/55 "2004-08-07T02:03:05Z")

</div>

> [@kirupa](#):
>
> What good is a 64-bit processor if you do not have applications running running in 64-bit. The reason I pick an Intel over AMD almost always is that, at least in the past, when the CPU overheated, Intel CPUs contained built-in technology that prevented the CPU from melting. Intel, in my view, simply makes better quality products. I would rather use the intel mobo reference designs over an AMD any day. My choice of Intel is part personal preference and part bad experiences with AMD in the past.
> 
> **That’s true, but more and more 64bit computers will ship within a year and when that happens, here comes the applications. AMD CPU’s does have a slight problem with heat, but what you paid is what you get.**
> 
> About the video card on the mobo, I’m going to have to disagree max! Nothing that is embedded on your motherboard is good. See I’m a Right Wing Conservative…when it comes to computers 😛 The motherboard has to have limited powers. The motherboard’s only job is the make sure that all its citizen PCI/AGP cards don’t run away. Something that is embedded means that it can’t be upgraded in the future, and if some hardware conflict occurs, you may have some issues trying to disable something that is attached to your motherboard. Impeaching troublesome hardware is more difficult if that hardware is stuck on the motherboard itself. Also, for the most part, graphics cards from reputable manufacturers such as Hercules, Sapphire, etc. don’t have a high likelihood of failing.
> 
> **Disabling pieces of the mobo isn’t hard, but from my experiences, it’s better to be safe. Does the extra 10 minutes to disable your onboard really matter? It doesn’t matter how bad your onboard is, it’s a backup, even 2MB is enough for onboard for its purposes.**
> 
> Also, AGP 8X is what you need for today’s games. Unlike 64-bit processing, old and new games will take advantage of the extra data throughput offered by AGP 8X.
> 
> **:trout: NO 8X! 4X!**
> 
> EDIT: Also, I’ve been tempted by ATI because of their lower prices (and I even bought a new ATI a few weeks ago!), but their shoddy driver support makes me regret my choice everytime. The new nVidia card is not all that bad, and it is capable of playing all new games. Better drivers imo are far better than a few fps that your eyes probably will never recognize.
> 
> **From what I’ve seen, most pros use hacked drivers that optimizes the GPU which is much more superior than the ATI drivers.**
> 
> :ub:

---

<div class="post-metadata">

**Author:** ![system](https://canada1.discourse-cdn.com/flex011/uploads/kirupa/original/3X/6/2/621e5c11736f46532526e61be85940af4230f3e5.png) [@system](https://forum.kirupa.com/u/system)\
**Post date:** [August 7, 2004, 2:05am UTC](https://forum.kirupa.com/t/buliding-my-own-computer-phase-1/59790/56 "2004-08-07T02:05:55Z")

</div>

kman: I have to disagree with you there on the AMD overheating part. I have tried overclocking my computer to almost that point and was able to use my processor again in about 1 hr. My friend who is a little more daring than I over heated his and still managed to use it again in 2.5hrs approx. Not only that, but I find that AMD processors are more, “overclockable” I guess you would say, in the sense that they can go higher and faster before becoming unstable.

also about nVidia drivers, I have a massive grudge against the driver because I cannot change many of my visual settings without it changing them back (I know it’s the driver because when I removed it the problems vanished) as for ATI, I haven’t had so much as an inconvienience with their driver. On my next computer, I’m going ATI all the way.

however, I do agree with you on the AGP front

edit: and one more thing, I will admit that AMD’s do pump out a lot of heat. My room temperature rises 7 degrees (Celcius) when I leave it on for 2+ hours.

note: I no longer overclock since that incident.

---

<div class="post-metadata">

**Author:** ![system](https://canada1.discourse-cdn.com/flex011/uploads/kirupa/original/3X/6/2/621e5c11736f46532526e61be85940af4230f3e5.png) [@system](https://forum.kirupa.com/u/system)\
**Post date:** [August 7, 2004, 2:11am UTC](https://forum.kirupa.com/t/buliding-my-own-computer-phase-1/59790/57 "2004-08-07T02:11:35Z")

</div>

Exactly. AMD processors are more tweakable than Intel. Intel tends to lock their speeds/frequencies. If you’re really hardcore, get some water cooling! If not, moderate your overclocking. When it’s a cold night, overclock it, when it’s hot during the day, dub it down to normal or even underclock it. I do it with my GFX.

---

<div class="post-metadata">

**Author:** ![system](https://canada1.discourse-cdn.com/flex011/uploads/kirupa/original/3X/6/2/621e5c11736f46532526e61be85940af4230f3e5.png) [@system](https://forum.kirupa.com/u/system)\
**Post date:** [August 7, 2004, 3:51am UTC](https://forum.kirupa.com/t/buliding-my-own-computer-phase-1/59790/58 "2004-08-07T03:51:48Z")

</div>

When it’s hot out I lie on the floor of the basement with a straw in my mouth leading to 2 cans of pop

@max: AMD processors are locked too, however AMD doesn’t appear to make much of an effort to support that as the Athalon T-Bird cores could be unlocked by a pencil stroke, and the XP ones could be unlocked through a simple (but delicate) method of masking, filling, and “painting” (with silver laquer). Not only that but some mobos are advertised to “unlock AMD processors” and finally to top it all off, the AMD +2500 Mobile has an unlocked multiplier that is ment for laptops, however can be used in desktop models - allowing you to get the most out of them as they run cooler than others, even when overclocking to +3200 levels. (It’s one of the alternatives that I’m looking at)

---

<div class="post-metadata">

**Author:** ![system](https://canada1.discourse-cdn.com/flex011/uploads/kirupa/original/3X/6/2/621e5c11736f46532526e61be85940af4230f3e5.png) [@system](https://forum.kirupa.com/u/system)\
**Post date:** [August 7, 2004, 4:17am UTC](https://forum.kirupa.com/t/buliding-my-own-computer-phase-1/59790/59 "2004-08-07T04:17:51Z")

</div>

Please note that in my previous post I was only stating what I would do.

I work for a local computer store when I’m home from college. If somebody came into the shop today and asked me to build them a kick butt computer, that is what I would build them. I have never used AMD or ATI products so I can’t really vouch for them…but I do know that Intel and NVidia make quality products and we have never had any trouble with them (within reason).

> 1. I would use an intel processor (what can I say? I’m an intel man). Pentium 4, hyperthreading, 800 mhz front side bus, prescott architecture.

Defeats the purpose of the 64bit processor doesn’t it?

I’m not really sure what you’re asking, could you restate your comment?

-teet

---

<div class="post-metadata">

**Author:** ![system](https://canada1.discourse-cdn.com/flex011/uploads/kirupa/original/3X/6/2/621e5c11736f46532526e61be85940af4230f3e5.png) [@system](https://forum.kirupa.com/u/system)\
**Post date:** [August 7, 2004, 4:22am UTC](https://forum.kirupa.com/t/buliding-my-own-computer-phase-1/59790/60 "2004-08-07T04:22:29Z")

</div>

Maybe I’m wrong, but Intel hasn’t made a commercial version of it’s 64bit chips correct? If so, you mentioned a 64bit processor, then you go onto Intel/Pentium 4.

[Previous page](https://forum.kirupa.com/t/buliding-my-own-computer-phase-1/59790.md?page=2)

[Next page](https://forum.kirupa.com/t/buliding-my-own-computer-phase-1/59790.md?page=4)
